Have you been interested in information around How to Install a Bathtub?
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the project can move immediately; if you need to open up a wall to eliminate the old bathtub as well as place the new tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the brand-new one. Make sure you have certified on your own for the work and are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you mount a brand-new bathtub in your shower room if you have actually already bought a new tub as well as do not need to transform the setup of your previous supply of water pipelines.
Your devices and product list ought to consist of the following:
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom should be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to make certain that the tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the tub till the level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water supply and also inspect all joints and new pipework for leakages and also tighten them if needed. Fill the bathtub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub should wait till the bathtub has actually been utilized at least when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the tap in place with the supplier offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, leading to complications with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about Installing A Bathtub? Place a remark further down. We would be glad to see your thoughts about this blog post. We hope to see you back again in the future. Loved our content? Please share it. Help other people find it. Thank you so much for going through it.
Request Your Service